Condition : Brand New
Warranty : 12 months
NEX Instrument Inc is not an authorized dealer, agent or associate of any of the designers, brands, or manufacturers, the products of which are offered for sale on www.nexinstrument.com. All trademarks, brand names, and logos mentioned are used for identification purposes only and are registered trademarks of their respective owners who reserve the right of ownership. The use of trademark, brand name or product on our website is not intended to suggest that the company, trademark or brand is affiliated to or endorses our website. All items are 100% authentic and legally purchased from authorized sources.
Estimated Lead Time: 5-7 Working Days
Manufacturer: Mitsubishi Electric
Ethernet interface block FX3U-ENET-ADP
Transmission Specifications Data transmission speed: 100Mbps or 10Mbps,
Communication mode: Full / half duplex
Transmission method: Baseband
The maximum segment length: 100m
The maximum number of nodes / connection: 10BASE-T: cascade up to four stages 100BASE-TX: cascade up to two-stage above is the connection possible number of stages at the time of use repeater hub. Can be connected to the number of stages at the time of switching hub used, please check with the manufacturer of the switching hub to be used.
function: · MELSOFT connection communicate by · MC protocol direct connection with · MELSOFT (simple connection) and connection CPU search function and time setting function ? time setting function (SNTP client), executable only after the establishment of the trigger conditions diagnosis from · MELSOFT function data monitoring function
Number of connections: MELSOFT connection + MC protocol + data monitoring ? 4 connection
It can be connected to the number of the basic unit: One Ethernet adapter, as well as the communication function expansion board and other communication special adapter, and 1 channel the communication channel (CH) occupation.
Apply PLC: FX3S, FX3G (V2.00 or later), FX3U (since V3.10), FX3GC (V2.00 or later), FX3UC (V3.10 or later) connection to the FX3S is required FX3S-CNV-ADP. Connection to the FX3G is required FX3G-CNV-ADP. FX3U, connection to the FX3UC-32MT-LT (-2), you must have the function expansion board.
Power supply: 30mA / DC5V (internal power supply from DC5V power of the basic unit)
Allowable momentary power failure time: As well as the sequencer to be connected
Ambient temperature: 0 ~ 55 °C ····· operation, -25 ~ 75 °C ····· during storage
Relative humidity: 5 ~ 95% RH (non-condensing) ...... operation
Vibration resistance When the DIN rail mounting Frequency: 10 ~ 57Hz: Half amplitude: 0.035mm X, Y, Z each direction 10 times (for a total of each 80 minutes)
Frequency: 57 ~ 150Hz: Acceleration: 4.9m / s2 X, Y, Z each direction 10 times (for a total of each 80 minutes)
Direct mounting at the time Frequency: 10 ~ 57Hz: Half amplitude: 0.075mm X, Y, Z each direction 10 times (for a total of each 80 minutes)
Frequency: 57 ~ 150Hz: Acceleration: 9.8m / s2 X, Y, Z each direction 10 times (for a total of each 80 minutes)
Impact resistance: 147m / s2, duration of action 11ms, X at half-sine pulse, Y, Z directions 3 times each
Anti-noise: Noise voltage 1,000Vp-p, noise width 1μs, due to rising 1ns, cycle 30 ~ 100Hz of noise simulator
Withstand voltage: All terminals and between the ground terminal: AC500V 1 minute
Insulation resistance: All terminals and between the ground terminal: DC500V 5MΩ more in insulation resistance tester
Working environment: Corrosive, there is no flammable gas, conductive dust (dust) that is not terribly
Use advanced: 2000m or less can not be used in the pressurized environment to more than atmospheric pressure. There is a possibility of failure.
Shipping Weight : 1 Kg