13% off
Mitsubishi Electric FX3U-1PG
Mitsubishi Electric FX3U-1PG

Mitsubishi Electric FX3U-1PG

0
0
5
USD338.00
USD388.70
USD50.70(13%)
Estimated Lead Time : Usually ships in 1 - 10 working days.
FX3U-1PG
Mitsubishi Electric

NII REF No : IAAI111911021121
  • Estimated Lead Time : Usually ships in 1 - 10 working days.

  • Manufacturer : Mitsubishi Electric

  • FX3U-1PG

  • Pulse output block FX 3 U - 1 PG

  • Number of control axes : 1 axis

  • Positioning program : Created by sequence program (use direct specification of buffer memory such as FROM / TO instruction or MOV instruction)

  • Positioning: -

  • method : Increment, Absolute

  • unit : PLS, µm, 10 -4 inch, mdeg

  • Unit magnification : 1, 10, 100, 1000 times

  • range : -2, 147, 483, 648 to 2, 147, 483, 647 PLS

  • Speed ??command : Hz, cm / min, inch / min, 10 deg / min

  • Output frequency : Output frequency 1 Hz to 200 kHz

  • Acceleration / deceleration processing : Trapezoidal acceleration / deceleration: 1 to 32,767 ms approximate S-shaped acceleration / deceleration: 1 to 5,000 ms

  • Start-up time : Motor system: 1 ms or less Mechanical system: 2 ms or less

  • Number of occupied I / O points : 8 points (It can count either input or output)

  • Application sequencer : About connection to FX5U, FX5UC CPU Unit> For connection to FX5U, FX5UC, FX5-CNV-BUS or FX5-CNV-BUSC are connected to FX5U, FX5U, FX3U (Ver.2.20 or later), FX3UC Is required. Depending on the system configuration, please choose either. To connect to FX3UC, FX2NC - CNV - IF or FX3UC - 1PS - 5V is required.

  • mass : About 0.2 kg

  • Power supply specification :

  • Drive power supply: -

  • For input signal : For input signal DC 24 V ± 10% Consumption current 40 mA or less

  • For output signal : For pulse output: DC 5 to 24 V DC consumption current 35 mA or less For CLR signal: DC 5 to 24 V DC consumption current 20 mA or less

  • For internal control : DC 5 V Consumption current 150 mA (Power is supplied from the sequencer body via extension cable)

  • Input specification: -

  • Input signal name: -

  • Group 1 STOP : Used for interrupt input during deceleration stop input or external command positioning, interruption 2-speed positioning operation

  • Group 1 DOG : DOG type Used for interrupt input during DOG input or external command positioning during machine home return operation, interrupt 1st speed positioning, interrupt stop, interrupt 2nd speed positioning operation

  • Group 2 PG 0 : Zero point signal input DOG type Used in machine home return operation

  • Group 1: -

  • Signal voltage : DC 24 V (power supplied from S / S terminal)

  • Input current : 7.0 mA

  • ON current : 4.5 mA or more

  • OFF current : 1.5 mA or less

  • Signal type : No-voltage contact input At sink input: NPN open collector transistor Source input: PNP open collector transistor

  • Response time : DOG input: 1 ms STOP input: 4 ms

  • Circuit insulation : Photocoupler insulation

  • Input operation display : LED ON when input is ON

  • Group 2: -

  • Signal voltage : DC 5 to 24 V

  • Input current : 20 mA or less

  • ON current : 4.0 mA or more

  • OFF current : 0.5 mA or less

  • Signal type : NPN open collector transistor

  • Response pulse width : 4 µs or more

  • Circuit insulation : Photocoupler insulation

  • Input operation display : LED ON when input is ON

  • Output specification :

  • Output signal name: -

  • Group 1 FP : Forward pulse or pulse train

  • RP : Reverse rotation pulse or rotation direction signal

  • Group 2 CLR : CLR signal

  • Group 1: -

  • Output format : A transistor

  • Output method : You can select forward rotation pulse (FP) / reverse rotation pulse (RP) or pulse (PLS) / direction (DIR)

  • Output frequency : 1 Hz to 200 kHz

  • Rated load voltage : DC 5 to 24 V

  • Maximum load current : 20 mA or less

  • VIN consumption current : DC 5 to 24 V 35 mA or less

  • Output ON voltage : Below 1.0V

  • Output operation indication : LED on when output is ON

  • Group 2: -

  • Output format : A transistor

  • Output method : Pulse (output pulse width: 20 ms)

  • Rated load voltage : DC 5 to 24 V

  • Maximum load current : 20 mA or less

  • Output ON voltage : 1.5V or less

  • Output operation indication : LED on when output is ON

  • Anti-vibration When DIN rail is installed Frequency: 10 to 57 Hz : One amplitude: 0.035 mm X, Y, Z 10 times in each direction (80 minutes in total)

  • Anti-vibration When DIN rail is installed Frequency: 57 to 150 Hz : Acceleration: 4.9 m / s 2 X, Y, Z 10 times in each direction (80 minutes in total)

  • Anti-vibration Direct installation Frequency: 10 to 57 Hz : One amplitude: 0.075 mm X, Y, Z 10 times in each direction (80 minutes in total)

  • Anti-vibration Direct installation Frequency: 57 to 150 Hz : Acceleration: 9.8 m / s 2 10 times in X, Y, Z directions (80 minutes in total)

  • Impact resistance : 147 m / s 2 , working time 11 ms, three times in X, Y, Z directions with a sine half-wave pulse

  • Noise immunity : Noise voltage with 1,000 Vp-p, noise width 1 µs, rising 1 ns, with noise si

  • tor with period of 30 to 100 Hz

  • Withstand voltage : Between all terminals and ground terminal: 500 VAC for 1 minute

  • Insulation resistance : Between all terminals and ground terminal: 500 MV DC 500 MO or more with an insulation resistance meter

  • Use atmosphere : There is no corrosive property, flammable gas, conductive dust (dust) is not serious

  • Use altitude : Can not be used in an environment pressurized to 2000 m or less under atmospheric pressure. It may break down.

  • Shipping Weight : 1.2 Kg

[short_review]
[long_review]
Did you find this helpful?  [rev_helpful] of [rev_votes] Found Helpful
Reviewed by: (Verified Buyer)  from [user_city]. [user_email] on [review_date]
[rating]
There are no reviews for this product!

Reward Points

338 points will be rewarded to you when you buy this item.

Related Items

https://www.nexinstrument.com/assets/images/Mitsubishi22052018/thumbnail/26.png

Feature 5

PRICE USD…..X1.6=USD…SELLING PRICE

Recently Viewed Items

Legal Disclaimer

NEX Instrument Inc is not an authorized dealer, agent or associate of any of the designers, brands, or manufacturers, the products of which are offered for sale on www.nexinstrument.com. All trademarks, brand names, and logos mentioned are used for identification purposes only and are registered trademarks of their respective owners who reserve the right of ownership. The use of trademark, brand name or product on our website is not intended to suggest that the company, trademark or brand is affiliated to or endorses our website. All items are 100% authentic and legally purchased from authorized sources.